Skip to content
Appliance & HVAC care across the East BayAppliance service dealer license A48849
WAVEAPPLIANCE REPAIR (925) 210-0900

Sub-Zero ice maker not working or not making ice

If your Sub-Zero ice maker is not working, start with the ice bin. An empty bin means you need to check ice production. Fresh cubes that will not come through the door point to a dispensing problem. If the freezer is warming up too, address the cooling problem first.

Send your request. WAVE will call to confirm a time.

Sub-Zero not making ice: four checks to start with

  • Ice maker setting. Confirm that ice production is turned on using the controls for your model.
  • Ice bin. Check that the bin sits level and fully in place. On some models, the bin operates a switch needed for production.
  • Freezer temperature. Sub-Zero recommends a 0°F setting and checking that the freezer is at or below 5°F when investigating no ice.
  • Water supply and filter. Confirm that the accessible supply valve is open. If your model has a filter, check its installation against the model’s instructions, especially after a recent replacement.

Keep these checks to accessible controls and parts covered by the owner’s guide. Leave panels, wiring and water-line disassembly to a technician. Do not chip away ice with a sharp tool or force a stuck mechanism.

Where is the ice maker control on a Classic BI or CL?

On a Legacy Classic BI, the control panel is along the top inside the refrigerator door. The Ice Maker key controls production, and a single illuminated cube indicates that it is on. On a Classic CL, open Settings on the home screen and use the ice cube control. Repeated taps cycle through on, Max Ice and off, so check the displayed mode before leaving the screen.

These instructions are specific to BI and CL models. A Designer, PRO or older series may use different controls. Match the full model number to its guide rather than assuming every Sub-Zero has the same reset button.

Model-specific ice maker symptoms

The model number helps identify the right controls and ice-making system. These examples cover Classic, Designer and 600 Series appliances. Use the complete model and serial number when checking instructions or ordering parts.

  • BI-36U: This Legacy Classic refrigerator/freezer makes ice in the freezer drawer. An empty bin can involve the ice setting, water supply or shut-off arm. On Classic over-and-under models, a detached or broken plastic rudder on that arm also needs attention. Do not force the arm. See Classic ice-maker troubleshooting.
  • BI-42SD and BI-48SD: These models have an external dispenser. If fresh cubes are in the bucket but none reach your glass, check for a locked dispenser, clumped ice or a bucket that is not seated correctly. No motor sound is a different observation from a motor that runs without moving ice. Use the dispenser checks.
  • CL4850SD/S: This newer Classic side-by-side also has a door dispenser, but its ice-maker control uses the CL touchscreen. Check the selected ice mode in Settings. Use CL control instructions rather than a BI button sequence.
  • IT-36CI: On this Designer refrigerator/freezer, check the ice setting, bin position and whether the freezer drawer has been opened and closed. Sub-Zero explains that Designer ice production automatically pauses after 20 cycles without a door or drawer opening. That pause can resemble a failure after a period of non-use. See Designer no-ice guidance.
  • 650: This 600 Series model uses an Ice On/Off key and displays ICE when enabled. A flashing Service Ice message means the water valve was energized for more than 15 seconds and ice production stopped. The message does not, by itself, prove that the valve needs replacing. See 600 Series troubleshooting.

What common ice-making symptoms can mean

Several faults can look like a failed ice maker. These are possible causes to investigate, not a parts diagnosis from the symptom alone.

  • Ice forms but will not drop: A trapped cube or an ice-maker mold heater failure can prevent ice from releasing. A recurring jam needs diagnosis; do not pry the cubes out. Sub-Zero describes both causes in its stuck-cube guidance.
  • The water fill tube keeps freezing: Water-pressure changes, a jam, or leaving the ice maker on while its water supply is off can contribute. Repeated freezing calls for service to find the cause. See our frozen ice-maker water-line guide and Sub-Zero’s explanation.
  • Cubes become small or hollow before production stops: Low water pressure is one possible explanation. Note a recent filter change or supply interruption, and have water flow checked before assuming the complete ice maker has failed. See our small or hollow ice-cube guide.

How long should you wait for the first ice?

After the appliance is first turned on or manually defrosted, the first cubes can take up to 24 hours. A few new cubes and an empty bin are different results: filling an empty bin can take about two days under normal conditions. Check whether new ice is being made, not just whether the bucket is full.

If an already-cold freezer stopped making ice immediately after a filter change, recheck that specific change. Confirm the replacement is correct for the model, follow its installation instructions and check whether the water supply was restored. The ice icon alone does not confirm that water is reaching the maker.

Is the freezer or refrigerator also losing cooling?

An empty ice bin plus softening frozen food needs more attention than an ice-only complaint. Note which compartment is affected and any temperature or service message on the display. Do not wait through a startup period when an established appliance is losing cooling.

For that combination of symptoms, see our Sub-Zero freezer not freezing guide. If the fresh-food compartment is also warm, use the Sub-Zero refrigerator not cooling guide and include both symptoms in your service request.

The bin has ice, but the dispenser does not work

On models with a door dispenser, check the dispenser lock and whether the ice is clumped together. Confirm that the bucket is seated correctly using the model’s instructions. Notice whether pressing the ice control produces motor noise or silence; that is useful information for diagnosis, but it does not identify a failed part by itself.

Fresh ice in the bin shows that production has occurred. Replacing the ice maker without checking the dispensing system may not address this symptom. If the bucket or mechanism is stuck, stop and request service instead of forcing it.

When to request Sub-Zero ice maker repair

Arrange diagnosis if the bin stays empty after the applicable checks and startup time, or if the problem keeps returning. Request help sooner for a leak, a jammed mechanism or loss of cooling. A technician can distinguish a supply, temperature, control or ice-maker fault before recommending parts.

WAVE offers independent Sub-Zero refrigerator repair in Walnut Creek and the East Bay. Tell us whether the bin is empty, ice is present but will not dispense, or the freezer is also warm. Include the model if readily available, when the problem started and whether it followed a filter change. You can request a visit without taking the appliance apart to find a label.

A separate undercounter ice machine needs its own model-specific checks. See Sub-Zero ice maker repair for that service request, or browse the Sub-Zero troubleshooting guides for other symptoms.

Manufacturer references: no-ice troubleshooting, BI controls, CL controls, production timing and dispenser checks. Follow the owner’s guide for your exact model.

(925) 210-0900 Call us now!